ability to connect securely
to a private network over a public network is
provided by which WAN
technology?
#VPN
3 Which three statements
describe the functions of the Cisco hierarchical network
design model? (Choose three.)
#The distribution layer is responsible for traffic filtering and isolating failures from
the core.
#Two goals of the core layer are 100 percent uptime and maximizing throughput.
The access layer provides a means of connecting end devices to the network.
design model? (Choose three.)
#The distribution layer is responsible for traffic filtering and isolating failures from
the core.
#Two goals of the core layer are 100 percent uptime and maximizing throughput.
The access layer provides a means of connecting end devices to the network.
4 A network designer is
creating a new network. The design must offer enough
redundancy to provide protection against a single link or device failure, yet must not be too
complex or expensive to implement. What topology would fill these needs?
#partial mesh
5 Refer to the exhibit. If the firewall module has been correctly configured using best practices for
network security, which statement is true about the security design for the network?
#Servers in the DMZ are protected from internal and external attacks.
6 Which statement is true about a DMZ in a traditional network firewall design?
#Servers in the DMZ provide limited information that can be accessed from external networks.
redundancy to provide protection against a single link or device failure, yet must not be too
complex or expensive to implement. What topology would fill these needs?
#partial mesh
5 Refer to the exhibit. If the firewall module has been correctly configured using best practices for
network security, which statement is true about the security design for the network?
#Servers in the DMZ are protected from internal and external attacks.
6 Which statement is true about a DMZ in a traditional network firewall design?
#Servers in the DMZ provide limited information that can be accessed from external networks.
7 download and upload
documents on the network file server. What network connection would be
most cost efficient while still meeting the security and connectivity needs of this teleworker?
#DSL VPN connection with a dialup backup link
8 Refer to the exhibit. The network administrator creates a standard access control list to prohibit
traffic from the 192.168.1.0/24 network from reaching the 192.168.2.0/24 network while still
permitting Internet access for all networks. On which router interface and in which direction
should it be applied?
#interface fa0/1, outbound
9 Refer to the exhibit. The server broadcasts an ARP request for the MAC address of its default
gateway. If STP is not enabled, what is the result of this ARP request?
#Switch_A and Switch_B continuously flood the message onto the network.
10 What are two best practices in wireless LAN design to ensure secure wireless
access to the corporate network? (Choose two.)
#Use a separate WLAN for employees.
#Configure WPA.
11 In a well-designed, high-availability network, which device significantly affects the
most users if a failure occurs?
#small workgroup switch in the network access layer
12 Which two statements are true regarding network convergence? (Choose two.)
#In a large network, using the EIGRP or OSPF routing protocols rather than RIPv2 may
improve convergence time.
#Route summarization improves convergence time by minimizing the size of the routing
table.
13 Centralizing servers in a data center server farm can provide which benefit over a
distributed server environment?
#It is easier to filter and prioritize traffic to and from the data center.
14 Refer to the exhibit. What effect does the ACL shown have on network traffic, assuming that it is
correctly applied to the interface?
#All Telnet traffic from the 172.16.0.0 network to any destination is denied.
15 Which Cisco IOS function can be configured at the distribution layer to filter
unwanted traffic and provide traffic management?
#access control lists
16 What kind of ACL inspects outbound UDP, TCP, and ICMP traffic and allows
inbound access only to traffic that belongs to these established sessions?
#reflexive ACL
17 Which three functions are performed at the distribution layer of the hierarchical
network model? (Choose three.)
#Summarizing routes from the access layer
#Isolating network problems to prevent them from affecting the core layer
#Utilizing redundant links for load balancing to increase available bandwidth
18 Refer to the exhibit. Which two devices are part of the access design layer? (Choose two.)
#FC-AP
#FC-ASW-2
19 What is true about implementing a centralized server farm topology?
#Provides defined entry and exit points so that filtering and securing traffic is easier
20 Refer to the exhibit. What happens when Host 1 attempts to send data?
#Frames from Host 1 cause the interface to shut down, and a log message is sent.
21 Which two considerations are valid when designing access layer security?(Choose two.)
#SSH is more secure than Telnet to administer network devices.
#Disabling unused ports on the switches helps prevent unauthorized access to the network.
22 What address can be used to summarize only networks 172.16.0.0/24, 172.16.1.0/24, 172.16.2.0/24, and 172.16.3.0/24?
#172.16.0.0/22
23 Which two items in a physical WLAN design can be identified through a site survey? (Choose two.)
#the types of antennas that are required
#the access point hardware that is required
24 Refer to the exhibit. Which two statements correctly describe the benefits of the network access layer design that is shown? (Choose two.)
#If host A sends a broadcast message, only hosts in VLAN10 receive the broadcast frame.
#Segmenting all voice traffic on a separate VLAN facilitates the implementation of QoS.
25 What are three ways to ensure that an unwanted user does not connect to a wireless network and view the data? (Choose three.)
#Disable SSID broadcasting.
#Use authentication between clients and the wireless device.
#Configure strong encryption such as WPA.
most cost efficient while still meeting the security and connectivity needs of this teleworker?
#DSL VPN connection with a dialup backup link
8 Refer to the exhibit. The network administrator creates a standard access control list to prohibit
traffic from the 192.168.1.0/24 network from reaching the 192.168.2.0/24 network while still
permitting Internet access for all networks. On which router interface and in which direction
should it be applied?
#interface fa0/1, outbound
9 Refer to the exhibit. The server broadcasts an ARP request for the MAC address of its default
gateway. If STP is not enabled, what is the result of this ARP request?
#Switch_A and Switch_B continuously flood the message onto the network.
10 What are two best practices in wireless LAN design to ensure secure wireless
access to the corporate network? (Choose two.)
#Use a separate WLAN for employees.
#Configure WPA.
11 In a well-designed, high-availability network, which device significantly affects the
most users if a failure occurs?
#small workgroup switch in the network access layer
12 Which two statements are true regarding network convergence? (Choose two.)
#In a large network, using the EIGRP or OSPF routing protocols rather than RIPv2 may
improve convergence time.
#Route summarization improves convergence time by minimizing the size of the routing
table.
13 Centralizing servers in a data center server farm can provide which benefit over a
distributed server environment?
#It is easier to filter and prioritize traffic to and from the data center.
14 Refer to the exhibit. What effect does the ACL shown have on network traffic, assuming that it is
correctly applied to the interface?
#All Telnet traffic from the 172.16.0.0 network to any destination is denied.
15 Which Cisco IOS function can be configured at the distribution layer to filter
unwanted traffic and provide traffic management?
#access control lists
16 What kind of ACL inspects outbound UDP, TCP, and ICMP traffic and allows
inbound access only to traffic that belongs to these established sessions?
#reflexive ACL
17 Which three functions are performed at the distribution layer of the hierarchical
network model? (Choose three.)
#Summarizing routes from the access layer
#Isolating network problems to prevent them from affecting the core layer
#Utilizing redundant links for load balancing to increase available bandwidth
18 Refer to the exhibit. Which two devices are part of the access design layer? (Choose two.)
#FC-AP
#FC-ASW-2
19 What is true about implementing a centralized server farm topology?
#Provides defined entry and exit points so that filtering and securing traffic is easier
20 Refer to the exhibit. What happens when Host 1 attempts to send data?
#Frames from Host 1 cause the interface to shut down, and a log message is sent.
21 Which two considerations are valid when designing access layer security?(Choose two.)
#SSH is more secure than Telnet to administer network devices.
#Disabling unused ports on the switches helps prevent unauthorized access to the network.
22 What address can be used to summarize only networks 172.16.0.0/24, 172.16.1.0/24, 172.16.2.0/24, and 172.16.3.0/24?
#172.16.0.0/22
23 Which two items in a physical WLAN design can be identified through a site survey? (Choose two.)
#the types of antennas that are required
#the access point hardware that is required
24 Refer to the exhibit. Which two statements correctly describe the benefits of the network access layer design that is shown? (Choose two.)
#If host A sends a broadcast message, only hosts in VLAN10 receive the broadcast frame.
#Segmenting all voice traffic on a separate VLAN facilitates the implementation of QoS.
25 What are three ways to ensure that an unwanted user does not connect to a wireless network and view the data? (Choose three.)
#Disable SSID broadcasting.
#Use authentication between clients and the wireless device.
#Configure strong encryption such as WPA.
Chapter2
1 During
an evaluation of the currently installed network, the IT staff performs a
gap analysis to determine whether the existing network infrastructure
can support the desired new features. At which stage of the Cisco
Lifecycle Services approach does this activity occur?
#Plan Phase
2 Which
stage of the Cisco Lifecycle Services strategy is usually
completed before an organization issues a Request For Proposal (RFP) or Request For Quotation (RFQ)?
#Prepare Phase
completed before an organization issues a Request For Proposal (RFP) or Request For Quotation (RFQ)?
#Prepare Phase
3 What is the
purpose of SNMP?
#to facilitate the exchange of information between devices and the NMS
4 During an analysis of a customer network, several possible
opportunities for network improvement are identified. At which stage of the Cisco Lifecycle Services does this process occur?
#Design Phase
5 What provides the initial data for the Optimize Phase?
#performance monitoring
6 Which two statements are true regarding the response to an RFQ?(Choose two.)
#it should strictly conform to the formatting requirements specified by the RFQ.
#The response helps the customer compare pricing with other potential contractors.
7 What are two disadvantages of using a bottom-up approach instead of a top-down approach to network design? (Choose two.)
#It can result in an inappropriate network design.
#It does not take into account the business goals of the company.
8 What is a business constraint that may impact the WAN design of a company?
#company policy requiring the use of specific vendor networking equipment due to partnerships
9 What is the purpose of preparing a business case?
#to justify the financial investment in implementing the technology change
10 What is the purpose of creating a prioritized list of technical requirements?
#defines the project scope
11 A network engineer is analyzing the network of a potential client company to identify problems and determine whether a network upgrade or addition is needed. Which role in the sales team is this engineer assuming?
#pre-sales engineer
12 Which two statements best describe the responsibilities of an
account manager? (Choose two.)
#acts as the primary point of contact between the company and the client
#directs the sales teams and support personnel
13 What is the purpose of system-level acceptance testing?
#to check that the newly installed network meets the business goals and design
requirements
14 What is a purpose of establishing a network baseline?
#It creates a point of reference for future network evaluations.
15 When should a network baseline be performed within the stages of the Cisco Lifecycle Services?
#Operate Phase
16 What are two benefits of using a top-down approach instead of a bottom-up approach to network design? (Choose two.)
#incorporates organizational requirements
#clarifies design goals from the perspective of applications and network solutions
17 Which software component is installed on network devices that are managed through SNMP?
#management agents
18 A network engineer working for a contracting company is
informed of a pre-bid meeting with a potential client. What purpose does the network engineer have for attending the pre-bid meeting?
#to clarify project scope and timelines not included in the original request for proposal
19 A major corporation has decided to hire someone to upgrade their network infrastructure. A network consulting company wants the job. What document must the network consulting company obtain to learn about the business goals, the project scope, the requirements for the new network and the expected deliverables?
#Request for Proposal
20 A corporation (client) wants a network upgrade and is putting out a request for services to various network consulting companies (contractors). A RFQ is required. Which statement is true concerning the RFQ?
#sent from the client to the contractors in place of a RFP when the technical specifications of a project are known
21 Which stage of the Cisco Lifecycle Services involves proactive
management to identify and resolve issues before the organization is affected?
#Optimize Phase
22 Why is it important to prioritize business goals when developing
network design?
#to adhere to the best opportunities to contribute to the success of the business
23 Which two items help identify business goals and priorities before a new network project starts? (Choose two.)
#motivation
#profitability
24 A network engineer working for ABC company is writing a
response to an RFP for a network upgrade and must create an executive summary. Which statement describes the basic components of an executive summary?
#quick overview of the problem, the recommended solution, and the justification for ABC company doing the job
25 In a network management architecture, which statement best
describes a management agent?
#software running on a managed device to collect network information and allow
that device to be managed by a management station
#to facilitate the exchange of information between devices and the NMS
4 During an analysis of a customer network, several possible
opportunities for network improvement are identified. At which stage of the Cisco Lifecycle Services does this process occur?
#Design Phase
5 What provides the initial data for the Optimize Phase?
#performance monitoring
6 Which two statements are true regarding the response to an RFQ?(Choose two.)
#it should strictly conform to the formatting requirements specified by the RFQ.
#The response helps the customer compare pricing with other potential contractors.
7 What are two disadvantages of using a bottom-up approach instead of a top-down approach to network design? (Choose two.)
#It can result in an inappropriate network design.
#It does not take into account the business goals of the company.
8 What is a business constraint that may impact the WAN design of a company?
#company policy requiring the use of specific vendor networking equipment due to partnerships
9 What is the purpose of preparing a business case?
#to justify the financial investment in implementing the technology change
10 What is the purpose of creating a prioritized list of technical requirements?
#defines the project scope
11 A network engineer is analyzing the network of a potential client company to identify problems and determine whether a network upgrade or addition is needed. Which role in the sales team is this engineer assuming?
#pre-sales engineer
12 Which two statements best describe the responsibilities of an
account manager? (Choose two.)
#acts as the primary point of contact between the company and the client
#directs the sales teams and support personnel
13 What is the purpose of system-level acceptance testing?
#to check that the newly installed network meets the business goals and design
requirements
14 What is a purpose of establishing a network baseline?
#It creates a point of reference for future network evaluations.
15 When should a network baseline be performed within the stages of the Cisco Lifecycle Services?
#Operate Phase
16 What are two benefits of using a top-down approach instead of a bottom-up approach to network design? (Choose two.)
#incorporates organizational requirements
#clarifies design goals from the perspective of applications and network solutions
17 Which software component is installed on network devices that are managed through SNMP?
#management agents
18 A network engineer working for a contracting company is
informed of a pre-bid meeting with a potential client. What purpose does the network engineer have for attending the pre-bid meeting?
#to clarify project scope and timelines not included in the original request for proposal
19 A major corporation has decided to hire someone to upgrade their network infrastructure. A network consulting company wants the job. What document must the network consulting company obtain to learn about the business goals, the project scope, the requirements for the new network and the expected deliverables?
#Request for Proposal
20 A corporation (client) wants a network upgrade and is putting out a request for services to various network consulting companies (contractors). A RFQ is required. Which statement is true concerning the RFQ?
#sent from the client to the contractors in place of a RFP when the technical specifications of a project are known
21 Which stage of the Cisco Lifecycle Services involves proactive
management to identify and resolve issues before the organization is affected?
#Optimize Phase
22 Why is it important to prioritize business goals when developing
network design?
#to adhere to the best opportunities to contribute to the success of the business
23 Which two items help identify business goals and priorities before a new network project starts? (Choose two.)
#motivation
#profitability
24 A network engineer working for ABC company is writing a
response to an RFP for a network upgrade and must create an executive summary. Which statement describes the basic components of an executive summary?
#quick overview of the problem, the recommended solution, and the justification for ABC company doing the job
25 In a network management architecture, which statement best
describes a management agent?
#software running on a managed device to collect network information and allow
that device to be managed by a management station
Chapter3
1 It
is important to identify the details of network sections and devices that will
be affected or involved in a new design. This information is included in
which section of the Network Design
Requirements Document?
Requirements Document?
#Project Scope
2 Which
two pieces of information does the network designer need to determine if the
Cisco IOS of a router requires an upgrade? (Choose two.)
#model number of the router
#installed
Cisco IOS feature set and version
3 Which three pieces of information need to be considered
when selecting the proper Cisco IOS version for an upgrade? (Choose
three.)
#amount of DRAM
#device make and model
#size of system flash memory
4 What are two practices a network technician should follow when installing a new interface card in a router? (Choose two.)
#Handle the interface card by the edges to avoid static discharge.
#Push the interface card into place until the edge connector is seated securely
5 The new serial interface card for the router arrives and the network technician reads that it is hotswappable. What does this mean?
#The card can be installed while the router is powered on if the router supports this technology.
6 Refer to the exhibit. A network administrator issues the command shown to gain knowledge about a poorly documented network. Which two pieces of information can the network administrator discover from the command output? (Choose two.)
#One connected device has router capability.
#Five Cisco devices with CDP enabled are directly connected to device C3750-24_MDF
7 Refer to the exhibit. Which of the three Cisco IOS images shown will load into RAM?
#The router selects an image depending on the boot system command in the configuration.
8 An administrator wants to download a new Cisco IOS software version to the local router. Which command performs this task?
#copy tftp flash
9 Refer to the exhibit. The top of the output shows the Cisco Feature Navigator regarding a Cisco IOS image that the administrator wants to install on a router. Below it is the output from the show version command for that router. Which statement is true regarding the capacity of the router to
run this Cisco IOS image?
#There is not enough DRAM and flash.
10 Which two items are objectives of a WLAN design site survey? (Choose two.)
#identify coverage areas
#determine primary AP locations
11 Refer to the exhibit. Which two actions improve the weaknesses of the topology shown, assuming that each access layer segment is in its own subnet? (Choose two.)
#Implement redundant links to each server by adding additional NICs.
#Implement a backup firewall with a link to a secondary ISP and implement a redundant link to the DMZ.
12 A company is beginning to analyze their new Cisco IOS upgrade requirements. What is one of the router components that a network administrator must consider when selecting a new Cisco IOS version?
#interfaces and modules to be supported
13 An employee at a company notices that the wireless signal strength indicator on his laptop fluctuates from good to low. The network administrator decides to do a site survey of that area.
Which three factors need to be included in the survey? (Choose three.)
#number of users in the area
#location of the AP
#location of walls and filing cabinets in the office
14 The new network design for AnyCompany must include support of voice and video traffic. Before upgrading, the network designer checks whether the existing devices can support the new
requirements. Which three items does the designer need to check? (Choose three.)
#size of DRAM and flash on each device
#routers that will support HWICs and VWICs
#modules supported on the loaded Cisco IOS
15 A new Cisco IOS version has been copied into flash from a TFTP server. When a reload is issued to upgrade the Cisco IOS, the router freezes part of the way through the loading process. What
could be the problem?
#There is enough flash but not enough RAM in the router.
16 Refer to the exhibit. A network designer has no documentation and is attempting to create a logical diagram of the network using the output from show commands. What can be determined
from the output shown?
#The designer cannot telnet to the attached switch.
17 A production router is reloaded and finishes with a Router> prompt. What three facts can be determined? (Choose three.)
#POST occurred normally.
#A full version of the Cisco IOS was located and loaded.
#A configuration file was not located in NVRAM or from a TFTP server.
18 During a site survey, the network designer noticed that people were accessing the company wireless network from the parking lot. What should be done to stop the wireless signal from
radiating out into the parking lot?
#change the type of antenna attached to the AP
19 A network design project includes a review of the existing network. What is the purpose of this phase of the project?
#To determine what existing network devices require upgrades to meet the new
20 Refer to the exhibit. Based upon the Cisco IOS file naming convention, what is represented by the value ipvoicek9 listed in the IOS filename?
#feature set
21 Refer to the exhibit. What two items can be determined from the output? (Choose two.)
#R2 is a Cisco 2600 device.
#The version of the IOS is 12.3.
22 During a wireless site survey, a consultant is determining the hours of peak usage and the estimated number of users in each location. The consultant is currently in what step of the site survey process?
#the identification of coverage areas
23 Refer to the exhibit. The network administrator is attempting to install a new version of the IOS on R2. Based on the exhibited output, what are two possible reasons that the transfer failed?(Choose two.)
#Connectivity between R2 and the TFTP server was not verified.
#The administrator did not verify that the TFTP server is running.
24 In which section of the Network Design Requirements document would a network consulting team detail names and IP addresses of important networking components and servers, provide network diagrams and topologies, and define strengths and weaknesses of the network?
#state of the network
#amount of DRAM
#device make and model
#size of system flash memory
4 What are two practices a network technician should follow when installing a new interface card in a router? (Choose two.)
#Handle the interface card by the edges to avoid static discharge.
#Push the interface card into place until the edge connector is seated securely
5 The new serial interface card for the router arrives and the network technician reads that it is hotswappable. What does this mean?
#The card can be installed while the router is powered on if the router supports this technology.
6 Refer to the exhibit. A network administrator issues the command shown to gain knowledge about a poorly documented network. Which two pieces of information can the network administrator discover from the command output? (Choose two.)
#One connected device has router capability.
#Five Cisco devices with CDP enabled are directly connected to device C3750-24_MDF
7 Refer to the exhibit. Which of the three Cisco IOS images shown will load into RAM?
#The router selects an image depending on the boot system command in the configuration.
8 An administrator wants to download a new Cisco IOS software version to the local router. Which command performs this task?
#copy tftp flash
9 Refer to the exhibit. The top of the output shows the Cisco Feature Navigator regarding a Cisco IOS image that the administrator wants to install on a router. Below it is the output from the show version command for that router. Which statement is true regarding the capacity of the router to
run this Cisco IOS image?
#There is not enough DRAM and flash.
10 Which two items are objectives of a WLAN design site survey? (Choose two.)
#identify coverage areas
#determine primary AP locations
11 Refer to the exhibit. Which two actions improve the weaknesses of the topology shown, assuming that each access layer segment is in its own subnet? (Choose two.)
#Implement redundant links to each server by adding additional NICs.
#Implement a backup firewall with a link to a secondary ISP and implement a redundant link to the DMZ.
12 A company is beginning to analyze their new Cisco IOS upgrade requirements. What is one of the router components that a network administrator must consider when selecting a new Cisco IOS version?
#interfaces and modules to be supported
13 An employee at a company notices that the wireless signal strength indicator on his laptop fluctuates from good to low. The network administrator decides to do a site survey of that area.
Which three factors need to be included in the survey? (Choose three.)
#number of users in the area
#location of the AP
#location of walls and filing cabinets in the office
14 The new network design for AnyCompany must include support of voice and video traffic. Before upgrading, the network designer checks whether the existing devices can support the new
requirements. Which three items does the designer need to check? (Choose three.)
#size of DRAM and flash on each device
#routers that will support HWICs and VWICs
#modules supported on the loaded Cisco IOS
15 A new Cisco IOS version has been copied into flash from a TFTP server. When a reload is issued to upgrade the Cisco IOS, the router freezes part of the way through the loading process. What
could be the problem?
#There is enough flash but not enough RAM in the router.
16 Refer to the exhibit. A network designer has no documentation and is attempting to create a logical diagram of the network using the output from show commands. What can be determined
from the output shown?
#The designer cannot telnet to the attached switch.
17 A production router is reloaded and finishes with a Router> prompt. What three facts can be determined? (Choose three.)
#POST occurred normally.
#A full version of the Cisco IOS was located and loaded.
#A configuration file was not located in NVRAM or from a TFTP server.
18 During a site survey, the network designer noticed that people were accessing the company wireless network from the parking lot. What should be done to stop the wireless signal from
radiating out into the parking lot?
#change the type of antenna attached to the AP
19 A network design project includes a review of the existing network. What is the purpose of this phase of the project?
#To determine what existing network devices require upgrades to meet the new
20 Refer to the exhibit. Based upon the Cisco IOS file naming convention, what is represented by the value ipvoicek9 listed in the IOS filename?
#feature set
21 Refer to the exhibit. What two items can be determined from the output? (Choose two.)
#R2 is a Cisco 2600 device.
#The version of the IOS is 12.3.
22 During a wireless site survey, a consultant is determining the hours of peak usage and the estimated number of users in each location. The consultant is currently in what step of the site survey process?
#the identification of coverage areas
23 Refer to the exhibit. The network administrator is attempting to install a new version of the IOS on R2. Based on the exhibited output, what are two possible reasons that the transfer failed?(Choose two.)
#Connectivity between R2 and the TFTP server was not verified.
#The administrator did not verify that the TFTP server is running.
24 In which section of the Network Design Requirements document would a network consulting team detail names and IP addresses of important networking components and servers, provide network diagrams and topologies, and define strengths and weaknesses of the network?
#state of the network
Chapter4
1. In
addition to the technical considerations, what other major factor is used to
evaluate the success of a network installation?
final project costs
maintenance costs
user satisfaction
statistics describing the performance of network devices
2. Which two network applications are most affected by network congestion and delays? (Choose two.)
IP telephony
live video webcasts
audio file downloads
online banking services
file archival and retrieval
3. What two Cisco tools can be used to analyze network application traffic? (Choose two.)
NBAR
NetFlow
AutoQoS
Wireshark
Custom Queuing
4. In network design, which technology can be implemented to prioritize traffic based on its importance and technical requirements?
STP
QoS RTP
TCP
VPN
5. What are two characteristics of voice over IP traffic? (Choose two.)
Voice packets tend to be small.
Voice packets must be processed in real time.
Voice packets can effectively use TCP reliability features.
Voice traffic can survive packet drops and retransmission delays.
Voice packets must be converted to analog before being sent across the IP network.
Voice packets automatically receive a higher priority value than other types of packets.
6. What are two things that a network designer can do to determine current and anticipated network traffic flows? (Choose two.)
Survey end users to obtain customer input.
Upgrade the Cisco IOS software in all networking devices to optimize traffic flow.
Limit the analysis to host-to-server traffic because host-to-host traffic is unimportant.
Run a network traffic analysis to determine which applications are in use and by whom.
Conduct an inventory of all networking devices that includes model numbers and memory configurations
7. A company that has a traditional telephone system wants to convert to IP telephony. Which two factors should be considered for the design? (Choose two.)
Digital communications systems have greater noise than analog systems when processing voice traffic.
Voice-enabled routers or a server must be used for call control and signaling. Voice to IP conversions can cause router overhead.
Power to the phones can be supplied through properly equipped patch panels or switches.
The cost to combine voice and data VLANs can be a considerable amount.
8. Several web and email servers have recently been installed as part of an enterprise network. The security administrator has been asked to provide a summary of security features that can be implemented to help prevent unauthorized traffic from being sent into or out of sensitive internal networks. Which three features should the security administrator recommend? (Choose three.)
firewalls priority queuing
access control lists
intrusion detection systems
DHCP
128-bit WEP
9. The design of an IP telephony system needs to meet the technical requirements to provide a connection to the PSTN as well as provide high-quality voice transmissions using the campus network. Which two elements directly affect the ability of the design to meet these requirements?(Choose two.)
voice-enabled firewall
PoE switches and patch panels
redundant backbone connectivity
voice-enabled router at the enterprise edge
separate voice and data VLANs with QoS implemented
10. When implementing VoIP services, which two design considerations should be followed?(Choose two.)
Confirm that network jitter is minimal.
Use TCP to reduce delays and dropped packets.
Establish priority queuing to ensure that large data packets are sent uninterrupted.
Disable real-time protocols to reduce queuing strategy demands.
Ensure that packet delays do not exceed 150 ms.
11. What design strategy should be followed when designing a network that uses video on demand?
implement the appropriate routing protocol to ensure that data segments arrive in order
implement different QoS queues based on the type of video traffic being distributed
install servers to store the data in a centrally located server farm
configure queuing in the core routers to ensure high availability
12. When implementing QoS in traffic queues, what is the first step the designer should take to ensure that traffic is properly prioritized?
define QoS policies
define traffic classes
determine traffic patterns
identify traffic requirements
identify networking equipment
13. Which two statements are characteristics of file transfer traffic flows? (Choose two.)
RTP should be used.
Traffic is predictable.
Packets are small in size.
Transfers are throughput intensive.
Response-time requirements are low.
14. Which two items can be determined by diagramming internal traffic flow? (Choose two.)
the type of ISP services needed
the capabilities of end-user devices
the areas where network congestion may occur
the location of VPN servers used to connect teleworkers
locations where high-bandwidth connections are required
15. Which two traffic types are examples of external traffic flows? (Choose two.)
A user in the IT department telnets to the core layer router.
A user in marketing connects to the web server of a competitor.
A user in the IT department telnets into the access layer switch.
A user in the services department logs in to a web-based email program.
A user in accounting connects to an FTP server that is connected to the access layer switch.
16. Which service can be provided by the NetFlow Cisco utility?
network planning and mapping
IDS and IPS capabilities
peak usage times and traffic routing
network billing and accounting application
security and user account restrictions
source and destination UDP port mapping
17. Refer to the exhibit. If ACL 150 identifies only voice traffic from network 192.168.10.0/24 and no other traffic, which queue will voice traffic from other networks use?
high
normal
medium
default
18. Refer to the exhibit. After configuring QoS, a network administrator issues the command show queueing interface s0/1. What two pieces of information can an administrator learn from the output of this command? (Choose two.)
queue traffic definitions
priority list protocol assignments
type of queuing being implemented
number of packets placed in each queue
queuing defaults that have been changed
queuing has not been applied to this interface
19. An analysis of network protocols reveals that RTP and RTCP are being used. What uses these protocols?
IDS
VPN
WLAN
firewall
real-time video
20. A company is considering adding voice and video to the data networks. Which two statements are true if voice and video are added? (Choose two.)
PoE switches must be purchased.
More UDP-based traffic flows will be evident.
Response times will be increased even if QoS is implemented.
QoS will most likely be implemented to prioritize traffic flows.
VPNs will most likely be implemented to protect the voice traffic.
21. Refer to the exhibit. Which option correctly matches the terms on top with its definition on the bottom?
A=1, B=3, C=2, D=4
A=2, B=1, C=4, D=3
A=2, B=4, C=1, D=3
A=3, B=2, C=4, D=1
A=4, B=3, C=1, D=2
A=4, B=2, C=3, D=1
22. A database server is configured to purge all data that is 60 days old. Ten data items that are 60 days old are to be purged. However, there is a failure halfway through the transaction, and the entire transaction is voided. What type of transaction action occurred?
atomic
consistent
durable
isolated
23. What is the primary goal of QoS?
classification of traffic
filtering and queuing voice traffic
reducing bandwidth requirements
providing priority service to selected traffic
24. Which technology provides a mechanism for implementing QoS at Layer 2?
ToS
CoS
DSCP
IP precedence
25. A customer purchases tickets online and pays using a credit card, but the system goes down before the transaction is complete. What transaction type retains a record of this transaction after the system failure so that the customer will still receive the tickets and the credit card account will be debited accordingly?
atomic
consistent
durable
isolated
26. Refer to the exhibit. The network design documents include requirements to prevent switching loops, to provide link-specific failover, and to provide Layer 3 recovery. Which two protocols would be needed to provide the support? (Choose two.)
HDLC
HSRP
PPP
RSTP VTP
27. network design must minimize latency to support real-time streaming applications. Which two protocols enable control and scalability of the network resources and minimize latency by incorporating QoS mechanisms? (Choose two.)
RTCP
HSRP
RSTP
RTP
RPC
28. Which two major differences are associated with IP telephony when compared to traditional telephony that uses a PBX? (Choose two.)
manages phones centrally
utilizes centralized call routing
creates peer-to-peer relationships between phones
requires a separate infrastructure to support data transfer
requires significant manual configuration when adding, moving, or changing phones
29. When QoS is implemented in a converged network, which two factors can be controlled to improve performance? (Choose two.)
link speed
delay
packet routing
jitter
packet addressing
final project costs
maintenance costs
user satisfaction
statistics describing the performance of network devices
2. Which two network applications are most affected by network congestion and delays? (Choose two.)
IP telephony
live video webcasts
audio file downloads
online banking services
file archival and retrieval
3. What two Cisco tools can be used to analyze network application traffic? (Choose two.)
NBAR
NetFlow
AutoQoS
Wireshark
Custom Queuing
4. In network design, which technology can be implemented to prioritize traffic based on its importance and technical requirements?
STP
QoS RTP
TCP
VPN
5. What are two characteristics of voice over IP traffic? (Choose two.)
Voice packets tend to be small.
Voice packets must be processed in real time.
Voice packets can effectively use TCP reliability features.
Voice traffic can survive packet drops and retransmission delays.
Voice packets must be converted to analog before being sent across the IP network.
Voice packets automatically receive a higher priority value than other types of packets.
6. What are two things that a network designer can do to determine current and anticipated network traffic flows? (Choose two.)
Survey end users to obtain customer input.
Upgrade the Cisco IOS software in all networking devices to optimize traffic flow.
Limit the analysis to host-to-server traffic because host-to-host traffic is unimportant.
Run a network traffic analysis to determine which applications are in use and by whom.
Conduct an inventory of all networking devices that includes model numbers and memory configurations
7. A company that has a traditional telephone system wants to convert to IP telephony. Which two factors should be considered for the design? (Choose two.)
Digital communications systems have greater noise than analog systems when processing voice traffic.
Voice-enabled routers or a server must be used for call control and signaling. Voice to IP conversions can cause router overhead.
Power to the phones can be supplied through properly equipped patch panels or switches.
The cost to combine voice and data VLANs can be a considerable amount.
8. Several web and email servers have recently been installed as part of an enterprise network. The security administrator has been asked to provide a summary of security features that can be implemented to help prevent unauthorized traffic from being sent into or out of sensitive internal networks. Which three features should the security administrator recommend? (Choose three.)
firewalls priority queuing
access control lists
intrusion detection systems
DHCP
128-bit WEP
9. The design of an IP telephony system needs to meet the technical requirements to provide a connection to the PSTN as well as provide high-quality voice transmissions using the campus network. Which two elements directly affect the ability of the design to meet these requirements?(Choose two.)
voice-enabled firewall
PoE switches and patch panels
redundant backbone connectivity
voice-enabled router at the enterprise edge
separate voice and data VLANs with QoS implemented
10. When implementing VoIP services, which two design considerations should be followed?(Choose two.)
Confirm that network jitter is minimal.
Use TCP to reduce delays and dropped packets.
Establish priority queuing to ensure that large data packets are sent uninterrupted.
Disable real-time protocols to reduce queuing strategy demands.
Ensure that packet delays do not exceed 150 ms.
11. What design strategy should be followed when designing a network that uses video on demand?
implement the appropriate routing protocol to ensure that data segments arrive in order
implement different QoS queues based on the type of video traffic being distributed
install servers to store the data in a centrally located server farm
configure queuing in the core routers to ensure high availability
12. When implementing QoS in traffic queues, what is the first step the designer should take to ensure that traffic is properly prioritized?
define QoS policies
define traffic classes
determine traffic patterns
identify traffic requirements
identify networking equipment
13. Which two statements are characteristics of file transfer traffic flows? (Choose two.)
RTP should be used.
Traffic is predictable.
Packets are small in size.
Transfers are throughput intensive.
Response-time requirements are low.
14. Which two items can be determined by diagramming internal traffic flow? (Choose two.)
the type of ISP services needed
the capabilities of end-user devices
the areas where network congestion may occur
the location of VPN servers used to connect teleworkers
locations where high-bandwidth connections are required
15. Which two traffic types are examples of external traffic flows? (Choose two.)
A user in the IT department telnets to the core layer router.
A user in marketing connects to the web server of a competitor.
A user in the IT department telnets into the access layer switch.
A user in the services department logs in to a web-based email program.
A user in accounting connects to an FTP server that is connected to the access layer switch.
16. Which service can be provided by the NetFlow Cisco utility?
network planning and mapping
IDS and IPS capabilities
peak usage times and traffic routing
network billing and accounting application
security and user account restrictions
source and destination UDP port mapping
17. Refer to the exhibit. If ACL 150 identifies only voice traffic from network 192.168.10.0/24 and no other traffic, which queue will voice traffic from other networks use?
high
normal
medium
default
18. Refer to the exhibit. After configuring QoS, a network administrator issues the command show queueing interface s0/1. What two pieces of information can an administrator learn from the output of this command? (Choose two.)
queue traffic definitions
priority list protocol assignments
type of queuing being implemented
number of packets placed in each queue
queuing defaults that have been changed
queuing has not been applied to this interface
19. An analysis of network protocols reveals that RTP and RTCP are being used. What uses these protocols?
IDS
VPN
WLAN
firewall
real-time video
20. A company is considering adding voice and video to the data networks. Which two statements are true if voice and video are added? (Choose two.)
PoE switches must be purchased.
More UDP-based traffic flows will be evident.
Response times will be increased even if QoS is implemented.
QoS will most likely be implemented to prioritize traffic flows.
VPNs will most likely be implemented to protect the voice traffic.
21. Refer to the exhibit. Which option correctly matches the terms on top with its definition on the bottom?
A=1, B=3, C=2, D=4
A=2, B=1, C=4, D=3
A=2, B=4, C=1, D=3
A=3, B=2, C=4, D=1
A=4, B=3, C=1, D=2
A=4, B=2, C=3, D=1
22. A database server is configured to purge all data that is 60 days old. Ten data items that are 60 days old are to be purged. However, there is a failure halfway through the transaction, and the entire transaction is voided. What type of transaction action occurred?
atomic
consistent
durable
isolated
23. What is the primary goal of QoS?
classification of traffic
filtering and queuing voice traffic
reducing bandwidth requirements
providing priority service to selected traffic
24. Which technology provides a mechanism for implementing QoS at Layer 2?
ToS
CoS
DSCP
IP precedence
25. A customer purchases tickets online and pays using a credit card, but the system goes down before the transaction is complete. What transaction type retains a record of this transaction after the system failure so that the customer will still receive the tickets and the credit card account will be debited accordingly?
atomic
consistent
durable
isolated
26. Refer to the exhibit. The network design documents include requirements to prevent switching loops, to provide link-specific failover, and to provide Layer 3 recovery. Which two protocols would be needed to provide the support? (Choose two.)
HDLC
HSRP
PPP
RSTP VTP
27. network design must minimize latency to support real-time streaming applications. Which two protocols enable control and scalability of the network resources and minimize latency by incorporating QoS mechanisms? (Choose two.)
RTCP
HSRP
RSTP
RTP
RPC
28. Which two major differences are associated with IP telephony when compared to traditional telephony that uses a PBX? (Choose two.)
manages phones centrally
utilizes centralized call routing
creates peer-to-peer relationships between phones
requires a separate infrastructure to support data transfer
requires significant manual configuration when adding, moving, or changing phones
29. When QoS is implemented in a converged network, which two factors can be controlled to improve performance? (Choose two.)
link speed
delay
packet routing
jitter
packet addressing
Chapter5
1 Which
rule should be followed when implementing the security requirements of a
network design?
#Avoid reducing security in order to add additional network capabilities.
#Avoid reducing security in order to add additional network capabilities.
2 What
limitations of the 2960 switch prevent it from providing the services needed in
the
Distribution layer?
Distribution layer?
#It does not support route
summarization.
3 When considering converged network designs, it is important to identify appropriate service demands. What is a concern when preparing a network design to fit this environment?
#voice-level quality of service
4 Which three design requirements are implemented at the access layer? (Choose three.)
#PoE
#VLANs
#QoS traffic classification and marking
5 Refer to the exhibit. Which statement is true regarding how the ISP router filters traffic?
#All traffic from the 64.100.0.0/21 network can access the Internet.
6 Which two factors should be considered when designing a wireless LAN that provides seamless roaming capabilities? (Choose two.)
#use of a wireless controller to manage IP addressing
#coverage
7 What are three features of a Catalyst 2960 switch? (Choose three.)
#redundant power availability
#SNMP
#switch clustering
8 A company lists this equipment in their network design:
Two Catalyst 4503 Layer 3 switches.
One 5500 security appliance firewall.
Two Catalyst 6509 switches.
Two lightweight access points.
Two Catalyst 2960 switches.
Which two types of devices would be appropriate to use at the access layer to provide end-user
connectivity? (Choose two.)
#lightweight access points
#Catalyst 2960 switches
9 Which two statements are true regarding the following extended ACL? (Choose two.)
#access-list 101 deny tcp 172.16.3.0 0.0.0.255 any eq 20
access-list 101 deny tcp 172.16.3.0 0.0.0.255 any eq 21
access-list 101 permit ip any any
#Telnet traffic originating on network 172.16.3.0/24 is denied.
10 Which statement applies to a large network with thousands of nodes?
#Intrusion detection is more likely to be performed by a separate device rather than integrated into a switch or router
11 on campus. The college currently has only wired network device access. Which two devices must be incorporated into the network design to best accommodate roaming for wireless IP phones?(Choose two.)
#Cisco wireless LAN controller
#lightweight access points
12 What type of WAN service is Frame Relay?
#packet switched
13 Refer to the exhibit. What is an advantage of having two links connected between the two switches shown?
#provides connectivity when one of the connections between the switches fails
14 What is the function of the access layer in the Cisco three-layer hierarchical internetworking model?
#provides QoS classification and marking
15 When applying network security, what security measure should be implemented first?
#securing the network devices
16 What characteristic of a network supports high availability?
#redundancy
17 What is integrated into a Cisco IP phone to reduce the number of ports needed in the wiring closet?
#switch
18 Which network design process identifies where to place access points?
#site survey
19 Using expandable, modular network devices is a key element of what network design criteria?
#scalability
20 What is a primary function of a wireless LAN controller?
#tuning each AP channel for optimal coverage
21 What characteristic in a routing protocol allows it to support the network design criteria for availability?
#fast convergence
22 A network designer is evaluating the network security implementation for an organization. The designer recommends adding network security devices in front of the server farm, although network security devices have been deployed in the Enterprise Edge for two years. What type of attack can be effectively prevented with this recommendation?
#internal attack
23 Refer to the exhibit. The branch office needs constant access to the servers in the enterprise headquarters. Therefore, a backup Frame Relay link is added. A network administrator is configuring the routers in the branch office to make sure that when the backup Frame Relay link is used, only the traffic to access the enterprise headquarters is allowed. Which statement is true about the routing configuration on branch office edge routers?
#The command ip route 128.107.0.0 255.255.0.0 serial 0/0 50 should be configured on BE2.
24 An automobile sales company is establishing a new, small sales showroom in a downtown area. To update the inventory database, the new sales office will need a WAN connection to the headquarters that is located in the suburban area. The WAN
connection should be around a 4 Mb/s connection. Which WAN service will provide the most economical approach to meet the requirement?
#DSL
25 A network designer is selecting a WAN technology for connections between the headquarters of an organization and its branch offices. In this context, what is one advantage of choosing Frame Relay over a T1 line?
#flexible bandwidth
Chapter6
1 A
network engineer researched whether there are mechanisms available to help with
the transition from an IPv4 addressing structure to IPv6. What three
options did the engineer find?(Choose three.)
#A protocol translation mechanism allows communication between the IPv4 and IPv6 networks.
#A protocol translation mechanism allows communication between the IPv4 and IPv6 networks.
#A dual-stack network design
allows both IPv4 and IPv6 addressing to be used on all network devices.
#Tunneling
allows IPv4 packets to be encapsulated so that they can traverse IPv6
networks and vice versa.
networks and vice versa.
2 When
should the command no auto-summary be used?
#with RIP version 2, when
discontigous networks exist
3 Refer to the exhibit. What must an administrator do on R3
to ensure that update packets are sent with subnet mask information?
#Add the commands:
R3(config-router)# version 2
R3(config-router)# no auto-summary
4 What best describes a discontiguous network?
#separated from the rest of the hierarchical group by another network
5 Refer to the exhibit. A company has decided to add a new workgroup. If the subnetting scheme for the network uses contiguous blocks of addresses, what subnet is assigned to WGROUP3?
#172.16.3.16/29
6 A network administrator is using the 10.0.0.0/8 network for the company. The administrator must create a masking scheme to support 750 users at the main office and 620 users at the remote
office. What mask should be assigned to the 10.0.0.0/8 network to preserve the most addresses?
#255.255.252.0
7 What is another format for the IPv6 address 1080:0000:0000:0000:0000:0000:1267:01A2?
#1080::1267:01A2
8 How many bits make up an IPv6 address?
#128
9 After activating IPv6 traffic forwarding, configuring IPv6 addresses, and globally configure RIPng, what is the remaining step to activate RIPng?
#Enter the interface mode for each IPv6 interface and enable RIPng with the ipv6 rip name enable command.
10 Refer to the exhibit. The IT management has determined that the new subnet for WGROUP3 needs to be broken down into four more subnets. What would the subnet mask be for the four newly created subnets within WGROUP3?
#255.255.192.0
11 Refer to the exhibit. What is the first usable IP address that can be assigned to the WGROUP3 switch?
#172.16.50.97/27
12 Refer to the exhibit. Which set of router commands is required to turn on unequal-cost load sharing so that RTRA selects the path A-B-E and the lowest cost path A-C-E to the Internet?
#RTRA(config)# router eigrp 1
RTRA(config-router)# variance 2
13 Refer to the exhibit. Assuming that the default EIGRP configuration is running on both routers, which statement is true about Router A reaching the 2.2.2.0/24 network?
#The no auto-summary command needs to be issued to disable automatic summarization.
14 Refer to the exhibit. The network administrator wants router RTA to send only the summarized route of 10.10.0.0/16 to RTC. Which configuration accomplishes this?
#RTA(config)# interface s0/1
RTA(config-if)# ip summary-address eigrp 101 10.10.0.0 255.255.0.0
RTA(config-if)# exit
RTA(config)# router eigrp 101
RTA(config-router)# no auto-summary
15 What is a good design practice when developing a hierarchical addressing scheme?
#Determine where statically configured addressing will be implemented.
16 A network administrator is asked to design a new addressing scheme for a corporate network. Presently, there are 850 users at the head office, 220 users at sales, 425 at manufacturing, and
50 at the research site. Which statement defines the correct VLSM addressing map with minimal waste using the 172.17.0.0/16 network?
#172.17.0.0/22 head office
172.17.4.0/23 manufacturing
172.17.5.0/24 sales
172.17.6.0/26 research
16 How would the routes for networks 172.16.1.0/24, 172.16.3.0/24, and 172.16.15.0/24 be summarized?
#172.16.0.0/20
17 What two advantages does CIDR provide to a network? (Choose two.)
#reduced routing update traffic
#easier management of summarization
18 Which statement describes MD5 authentication for neighbor authentication?
#All passwords are sent in clear text when neighbors first learn about each other.
19 Refer to the exhibit. What are the broadcast addresses for each subnet?
#Admin - 172.16.31.255
QA - 172.16.1.127
Development - 172.16.3.255
Sales - 172.16.63.255
20 Refer to the exhibit. The IT management is adding three VLANs to the wgroup3 switch. The current subnet will be broken down to support 14 hosts for each of the new VLANs. What will the new subnet mask be for these VLANs?
#255.255.255.240
21 An administrator is configuring IPv6 on a router. The steps that have already been completed are:
1. Activate IPv6 traffic forwarding.
2. Configure IPv6 addresses.
3. Globally configure RIPng.
What is the remaining step to complete the activation of RIPng?
#Enter the interface mode for each IPv6 interface and enable RIPng with the ipv6 rip name enable command.
22 Which range includes all available networks in the 192.168.8.0/21 network?
192.168.8.0/24 - 192.168.15.0/24
23 Which two are best practices for creating a new IP addressing
scheme for a network? (Choose two.)
#Plan and allow for significant growth.
#Plan the entire addressing scheme before assigning any addresses.
24 Refer to the exhibit. Which subnet will provide sufficient addresses for the Production network with minimal waste?
#172.16.0.192/27
25 A network designer is implementing a new network for a company. The designer is using all new Cisco equipment and has decided to select a hierarchical routing protocol for the network. The designer wishes to minimize traffic from routing
updates but also needs fast routing convergence in the event of a topology change. Also, the existing IP addressing scheme requires that the selected protocol support VLSM. Which routing protocol should be chosen?
#OSPF
#Add the commands:
R3(config-router)# version 2
R3(config-router)# no auto-summary
4 What best describes a discontiguous network?
#separated from the rest of the hierarchical group by another network
5 Refer to the exhibit. A company has decided to add a new workgroup. If the subnetting scheme for the network uses contiguous blocks of addresses, what subnet is assigned to WGROUP3?
#172.16.3.16/29
6 A network administrator is using the 10.0.0.0/8 network for the company. The administrator must create a masking scheme to support 750 users at the main office and 620 users at the remote
office. What mask should be assigned to the 10.0.0.0/8 network to preserve the most addresses?
#255.255.252.0
7 What is another format for the IPv6 address 1080:0000:0000:0000:0000:0000:1267:01A2?
#1080::1267:01A2
8 How many bits make up an IPv6 address?
#128
9 After activating IPv6 traffic forwarding, configuring IPv6 addresses, and globally configure RIPng, what is the remaining step to activate RIPng?
#Enter the interface mode for each IPv6 interface and enable RIPng with the ipv6 rip name enable command.
10 Refer to the exhibit. The IT management has determined that the new subnet for WGROUP3 needs to be broken down into four more subnets. What would the subnet mask be for the four newly created subnets within WGROUP3?
#255.255.192.0
11 Refer to the exhibit. What is the first usable IP address that can be assigned to the WGROUP3 switch?
#172.16.50.97/27
12 Refer to the exhibit. Which set of router commands is required to turn on unequal-cost load sharing so that RTRA selects the path A-B-E and the lowest cost path A-C-E to the Internet?
#RTRA(config)# router eigrp 1
RTRA(config-router)# variance 2
13 Refer to the exhibit. Assuming that the default EIGRP configuration is running on both routers, which statement is true about Router A reaching the 2.2.2.0/24 network?
#The no auto-summary command needs to be issued to disable automatic summarization.
14 Refer to the exhibit. The network administrator wants router RTA to send only the summarized route of 10.10.0.0/16 to RTC. Which configuration accomplishes this?
#RTA(config)# interface s0/1
RTA(config-if)# ip summary-address eigrp 101 10.10.0.0 255.255.0.0
RTA(config-if)# exit
RTA(config)# router eigrp 101
RTA(config-router)# no auto-summary
15 What is a good design practice when developing a hierarchical addressing scheme?
#Determine where statically configured addressing will be implemented.
16 A network administrator is asked to design a new addressing scheme for a corporate network. Presently, there are 850 users at the head office, 220 users at sales, 425 at manufacturing, and
50 at the research site. Which statement defines the correct VLSM addressing map with minimal waste using the 172.17.0.0/16 network?
#172.17.0.0/22 head office
172.17.4.0/23 manufacturing
172.17.5.0/24 sales
172.17.6.0/26 research
16 How would the routes for networks 172.16.1.0/24, 172.16.3.0/24, and 172.16.15.0/24 be summarized?
#172.16.0.0/20
17 What two advantages does CIDR provide to a network? (Choose two.)
#reduced routing update traffic
#easier management of summarization
18 Which statement describes MD5 authentication for neighbor authentication?
#All passwords are sent in clear text when neighbors first learn about each other.
19 Refer to the exhibit. What are the broadcast addresses for each subnet?
#Admin - 172.16.31.255
QA - 172.16.1.127
Development - 172.16.3.255
Sales - 172.16.63.255
20 Refer to the exhibit. The IT management is adding three VLANs to the wgroup3 switch. The current subnet will be broken down to support 14 hosts for each of the new VLANs. What will the new subnet mask be for these VLANs?
#255.255.255.240
21 An administrator is configuring IPv6 on a router. The steps that have already been completed are:
1. Activate IPv6 traffic forwarding.
2. Configure IPv6 addresses.
3. Globally configure RIPng.
What is the remaining step to complete the activation of RIPng?
#Enter the interface mode for each IPv6 interface and enable RIPng with the ipv6 rip name enable command.
22 Which range includes all available networks in the 192.168.8.0/21 network?
192.168.8.0/24 - 192.168.15.0/24
23 Which two are best practices for creating a new IP addressing
scheme for a network? (Choose two.)
#Plan and allow for significant growth.
#Plan the entire addressing scheme before assigning any addresses.
24 Refer to the exhibit. Which subnet will provide sufficient addresses for the Production network with minimal waste?
#172.16.0.192/27
25 A network designer is implementing a new network for a company. The designer is using all new Cisco equipment and has decided to select a hierarchical routing protocol for the network. The designer wishes to minimize traffic from routing
updates but also needs fast routing convergence in the event of a topology change. Also, the existing IP addressing scheme requires that the selected protocol support VLSM. Which routing protocol should be chosen?
#OSPF
Chapter7
1 A
network engineer has decided to pilot test a portion of a new network design
rather than rely on a prototype for proof-of-concept. What are two
advantages of pilot testing a design concept?(Choose two.)
#The test network experiences real-world network traffic.
#The test network experiences real-world network traffic.
#Network response can be tested
in unplanned and unpredictable situations.
2 While
preparing a network test plan document, a network designer records all initial
and modified device configurations. Which section of the document
typically contains this information?
#Appendix
#Appendix
3 Refer to the exhibit. A network designer creates a test
plan that includes the specification shown. In which section of the test
plan would this specification be found?
#Anticipated Results and Success Criteria
4 What OSI model Layer 2 security measure can a network engineer implement when prototyping network security?
#port security at the access design layer
5 How do designers decide which network functions need to be included in the prototype test?
#They select the functions that align with the business goals.
6 Refer to the exhibit. During prototype testing of the Cisco network shown, connectivity must be verified. Assuming all connections are working and CDP is enabled on all devices and interfaces, on which device was the command issued?
#R1
7 Refer to the exhibit. During prototyping, Layer 2 functionality is being tested. Based on the output shown, which two pieces of information can be determined? (Choose two.)
#Interface Fa0/2 on Switch1 is the alternate port used to reach the root bridge.
#Based on the entries in the "Role" column, it can be concluded that RSTP has been implemented.
8 What Rapid Spanning Tree Protocol (RSTP) state is given to the forwarding port elected for every switched Ethernet LAN segment?
#designated
9 Refer to the exhibit. During prototype testing, verification of VLAN connectivity is being performed. Based on the information shown, what command produced the output?
#show interfaces trunk
10 Switch port Fa0/24 was previously configured as a trunk, but now it is to be used to connect a host to the network. How should the network administrator reconfigure switch port Fa0/24?
#Use the switchport mode access command from interface configuration mode.
11 Refer to the exhibit. The redundant paths are of equal bandwidth and EIGRP is the routing protocol in use. Which statement describes the data flow from Server to PC2?
#EIGRP load balances across the R3 to R1 and R3 to R2 links.
12 A network designer needs to determine if a proposed IP addressing scheme allows efficient route summarization and provides the appropriate amount of scalability to a design. What is useful for validating a proposed hierarchical IP addressing scheme?
#a network simulator
13 In the router command encapsulation dot1q 10, what does the number 10 represent?
#the number of the VLAN associated with the encapsulated subinterface
14 Refer to the exhibit. The users on the 192.168.10.192 network are not allowed Internet access.The network design calls for an extended ACL to be developed and tested. Where should the
ACL be placed for the least effect on other network traffic?
#inbound on Fa0/1 of R3
15 Refer to the exhibit. What two measures can be taken to address the areas of weakness circled in the network design? (Choose two.)
#Add a switch in the server block connecting the server farm to each core switch.
#Provide a redundant firewall router connecting to a second ISP, the core switches, and the DMZ.
16 Why is it important to record baseline measurements of a prototype network?
#Test results are compared to the baseline to see how the test conditions increase processor use or decrease available bandwidth.
17 Refer to the exhibit. A network administrator has been given the task of creating a design for a temporary classroom building that is to be set up outside an overcrowded school. In testing the prototype, it is found that the student PC cannot ping the teacher PC. All the switch interfaces are active and connected properly, as is interface Fa0/0 of the router. Given that only the commands shown have been added to the router configuration, what is the source of the problem?
#The IP settings on the student PC are incorrect.
18 Refer to the exhibit. Why are interfaces Fa0/11, Fa0/23, and Fa0/24 not shown in this switch output?
#Interfaces Fa0/11, Fa0/23, and Fa0/24 are trunks.
19 Refer to the exhibit. A network technician is performing an initial installation of a new switch in the east wing. The technician removes the switch from the box, makes the connections to the network, and adds the configuration shown. The technician notifies the network administrator that the switch has been installed. When the network administrator at the home office attempts to telnet to the switch from host 192.168.0.1, the connection fails. What action should the network
technician take?
#Add a default gateway to the switch configuration.
20 Refer to the exhibit. After all the interfaces have stabilized, what is the spanning-tree state of all the enabled interfaces of SW11?
#forwarding
#Anticipated Results and Success Criteria
4 What OSI model Layer 2 security measure can a network engineer implement when prototyping network security?
#port security at the access design layer
5 How do designers decide which network functions need to be included in the prototype test?
#They select the functions that align with the business goals.
6 Refer to the exhibit. During prototype testing of the Cisco network shown, connectivity must be verified. Assuming all connections are working and CDP is enabled on all devices and interfaces, on which device was the command issued?
#R1
7 Refer to the exhibit. During prototyping, Layer 2 functionality is being tested. Based on the output shown, which two pieces of information can be determined? (Choose two.)
#Interface Fa0/2 on Switch1 is the alternate port used to reach the root bridge.
#Based on the entries in the "Role" column, it can be concluded that RSTP has been implemented.
8 What Rapid Spanning Tree Protocol (RSTP) state is given to the forwarding port elected for every switched Ethernet LAN segment?
#designated
9 Refer to the exhibit. During prototype testing, verification of VLAN connectivity is being performed. Based on the information shown, what command produced the output?
#show interfaces trunk
10 Switch port Fa0/24 was previously configured as a trunk, but now it is to be used to connect a host to the network. How should the network administrator reconfigure switch port Fa0/24?
#Use the switchport mode access command from interface configuration mode.
11 Refer to the exhibit. The redundant paths are of equal bandwidth and EIGRP is the routing protocol in use. Which statement describes the data flow from Server to PC2?
#EIGRP load balances across the R3 to R1 and R3 to R2 links.
12 A network designer needs to determine if a proposed IP addressing scheme allows efficient route summarization and provides the appropriate amount of scalability to a design. What is useful for validating a proposed hierarchical IP addressing scheme?
#a network simulator
13 In the router command encapsulation dot1q 10, what does the number 10 represent?
#the number of the VLAN associated with the encapsulated subinterface
14 Refer to the exhibit. The users on the 192.168.10.192 network are not allowed Internet access.The network design calls for an extended ACL to be developed and tested. Where should the
ACL be placed for the least effect on other network traffic?
#inbound on Fa0/1 of R3
15 Refer to the exhibit. What two measures can be taken to address the areas of weakness circled in the network design? (Choose two.)
#Add a switch in the server block connecting the server farm to each core switch.
#Provide a redundant firewall router connecting to a second ISP, the core switches, and the DMZ.
16 Why is it important to record baseline measurements of a prototype network?
#Test results are compared to the baseline to see how the test conditions increase processor use or decrease available bandwidth.
17 Refer to the exhibit. A network administrator has been given the task of creating a design for a temporary classroom building that is to be set up outside an overcrowded school. In testing the prototype, it is found that the student PC cannot ping the teacher PC. All the switch interfaces are active and connected properly, as is interface Fa0/0 of the router. Given that only the commands shown have been added to the router configuration, what is the source of the problem?
#The IP settings on the student PC are incorrect.
18 Refer to the exhibit. Why are interfaces Fa0/11, Fa0/23, and Fa0/24 not shown in this switch output?
#Interfaces Fa0/11, Fa0/23, and Fa0/24 are trunks.
19 Refer to the exhibit. A network technician is performing an initial installation of a new switch in the east wing. The technician removes the switch from the box, makes the connections to the network, and adds the configuration shown. The technician notifies the network administrator that the switch has been installed. When the network administrator at the home office attempts to telnet to the switch from host 192.168.0.1, the connection fails. What action should the network
technician take?
#Add a default gateway to the switch configuration.
20 Refer to the exhibit. After all the interfaces have stabilized, what is the spanning-tree state of all the enabled interfaces of SW11?
#forwarding
Chapter8
1 A
network engineer has decided to pilot test a portion of a new network design
rather than rely on a prototype for proof-of-concept. What are two
advantages of pilot testing a design concept?(Choose two.)
#The test network experiences real-world network traffic.
#The test network experiences real-world network traffic.
#Network response can be tested
in unplanned and unpredictable situations.
2 While
preparing a network test plan document, a network designer records all initial
and modified device configurations. Which section of the document
typically contains this information?
#Appendix
#Appendix
3 Refer to the exhibit. A network designer creates a test
plan that includes the specification shown. In which section of the test
plan would this specification be found?
#Anticipated Results and Success Criteria
4 What OSI model Layer 2 security measure can a network engineer implement when prototyping network security?
#port security at the access design layer
5 How do designers decide which network functions need to be included in the prototype test?
#They select the functions that align with the business goals.
6 Refer to the exhibit. During prototype testing of the Cisco network shown, connectivity must be verified. Assuming all connections are working and CDP is enabled on all devices and interfaces, on which device was the command issued?
#R1
7 Refer to the exhibit. During prototyping, Layer 2 functionality is being tested. Based on the output shown, which two pieces of information can be determined? (Choose two.)
#Interface Fa0/2 on Switch1 is the alternate port used to reach the root bridge.
#Based on the entries in the "Role" column, it can be concluded that RSTP has been implemented.
8 What Rapid Spanning Tree Protocol (RSTP) state is given to the forwarding port elected for every switched Ethernet LAN segment?
#designated
9 Refer to the exhibit. During prototype testing, verification of VLAN connectivity is being performed. Based on the information shown, what command produced the output?
#show interfaces trunk
10 Switch port Fa0/24 was previously configured as a trunk, but now it is to be used to connect a host to the network. How should the network administrator reconfigure switch port Fa0/24?
#Use the switchport mode access command from interface configuration mode.
11 Refer to the exhibit. The redundant paths are of equal bandwidth and EIGRP is the routing protocol in use. Which statement describes the data flow from Server to PC2?
#EIGRP load balances across the R3 to R1 and R3 to R2 links.
12 A network designer needs to determine if a proposed IP addressing scheme allows efficient route summarization and provides the appropriate amount of scalability to a design. What is useful for validating a proposed hierarchical IP addressing scheme?
#a network simulator
13 In the router command encapsulation dot1q 10, what does the number 10 represent?
#the number of the VLAN associated with the encapsulated subinterface
14 Refer to the exhibit. The users on the 192.168.10.192 network are not allowed Internet access.The network design calls for an extended ACL to be developed and tested. Where should the
ACL be placed for the least effect on other network traffic?
#inbound on Fa0/1 of R3
15 Refer to the exhibit. What two measures can be taken to address the areas of weakness circled in the network design? (Choose two.)
#Add a switch in the server block connecting the server farm to each core switch.
#Provide a redundant firewall router connecting to a second ISP, the core switches, and the DMZ.
16 Why is it important to record baseline measurements of a prototype network?
#Test results are compared to the baseline to see how the test conditions increase processor use or decrease available bandwidth.
17 Refer to the exhibit. A network administrator has been given the task of creating a design for a temporary classroom building that is to be set up outside an overcrowded school. In testing the prototype, it is found that the student PC cannot ping the teacher PC. All the switch interfaces are active and connected properly, as is interface Fa0/0 of the router. Given that only the commands shown have been added to the router configuration, what is the source of the problem?
#The IP settings on the student PC are incorrect.
18 Refer to the exhibit. Why are interfaces Fa0/11, Fa0/23, and Fa0/24 not shown in this switch output?
#Interfaces Fa0/11, Fa0/23, and Fa0/24 are trunks.
19 Refer to the exhibit. A network technician is performing an initial installation of a new switch in the east wing. The technician removes the switch from the box, makes the connections to the network, and adds the configuration shown. The technician notifies the network administrator that the switch has been installed. When the network administrator at the home office attempts to telnet to the switch from host 192.168.0.1, the connection fails. What action should the network
technician take?
#Add a default gateway to the switch configuration.
20 Refer to the exhibit. After all the interfaces have stabilized, what is the spanning-tree state of all the enabled interfaces of SW11?
#forwarding
#Anticipated Results and Success Criteria
4 What OSI model Layer 2 security measure can a network engineer implement when prototyping network security?
#port security at the access design layer
5 How do designers decide which network functions need to be included in the prototype test?
#They select the functions that align with the business goals.
6 Refer to the exhibit. During prototype testing of the Cisco network shown, connectivity must be verified. Assuming all connections are working and CDP is enabled on all devices and interfaces, on which device was the command issued?
#R1
7 Refer to the exhibit. During prototyping, Layer 2 functionality is being tested. Based on the output shown, which two pieces of information can be determined? (Choose two.)
#Interface Fa0/2 on Switch1 is the alternate port used to reach the root bridge.
#Based on the entries in the "Role" column, it can be concluded that RSTP has been implemented.
8 What Rapid Spanning Tree Protocol (RSTP) state is given to the forwarding port elected for every switched Ethernet LAN segment?
#designated
9 Refer to the exhibit. During prototype testing, verification of VLAN connectivity is being performed. Based on the information shown, what command produced the output?
#show interfaces trunk
10 Switch port Fa0/24 was previously configured as a trunk, but now it is to be used to connect a host to the network. How should the network administrator reconfigure switch port Fa0/24?
#Use the switchport mode access command from interface configuration mode.
11 Refer to the exhibit. The redundant paths are of equal bandwidth and EIGRP is the routing protocol in use. Which statement describes the data flow from Server to PC2?
#EIGRP load balances across the R3 to R1 and R3 to R2 links.
12 A network designer needs to determine if a proposed IP addressing scheme allows efficient route summarization and provides the appropriate amount of scalability to a design. What is useful for validating a proposed hierarchical IP addressing scheme?
#a network simulator
13 In the router command encapsulation dot1q 10, what does the number 10 represent?
#the number of the VLAN associated with the encapsulated subinterface
14 Refer to the exhibit. The users on the 192.168.10.192 network are not allowed Internet access.The network design calls for an extended ACL to be developed and tested. Where should the
ACL be placed for the least effect on other network traffic?
#inbound on Fa0/1 of R3
15 Refer to the exhibit. What two measures can be taken to address the areas of weakness circled in the network design? (Choose two.)
#Add a switch in the server block connecting the server farm to each core switch.
#Provide a redundant firewall router connecting to a second ISP, the core switches, and the DMZ.
16 Why is it important to record baseline measurements of a prototype network?
#Test results are compared to the baseline to see how the test conditions increase processor use or decrease available bandwidth.
17 Refer to the exhibit. A network administrator has been given the task of creating a design for a temporary classroom building that is to be set up outside an overcrowded school. In testing the prototype, it is found that the student PC cannot ping the teacher PC. All the switch interfaces are active and connected properly, as is interface Fa0/0 of the router. Given that only the commands shown have been added to the router configuration, what is the source of the problem?
#The IP settings on the student PC are incorrect.
18 Refer to the exhibit. Why are interfaces Fa0/11, Fa0/23, and Fa0/24 not shown in this switch output?
#Interfaces Fa0/11, Fa0/23, and Fa0/24 are trunks.
19 Refer to the exhibit. A network technician is performing an initial installation of a new switch in the east wing. The technician removes the switch from the box, makes the connections to the network, and adds the configuration shown. The technician notifies the network administrator that the switch has been installed. When the network administrator at the home office attempts to telnet to the switch from host 192.168.0.1, the connection fails. What action should the network
technician take?
#Add a default gateway to the switch configuration.
20 Refer to the exhibit. After all the interfaces have stabilized, what is the spanning-tree state of all the enabled interfaces of SW11?
#forwarding
Chapter9
1 Which
two statements describe factors that influence the layout of a proposal?
(Choose two.)
#A specific proposal layout is
followed when one is specified in the RFP.
#A designer
chooses the layout if a written RFP does not specify an outline.
2 What
two items are typically included in the executive summary of a proposal?
(Choose two.)
#project scope summary
#project scope summary
#emphasis on the benefits that
meet the goals of the customer
3 Which proposal section describes the intended routing
protocol, security mechanisms, and addressing for the planned network?
#logical design
4 Which occurrence would indicate a failure of the design phase?
#The new network capacity is inadequate to support required traffic.
5 A network installation team is assigned to replace all core switches in an existing data center. No other upgrades are planned. Which kind of installation is this?
#a phased installation
6 What service is provided Cisco standard warranty?
#replacement of defected hardware
7 An upgraded version of the Cisco IOS has been purchased. However, the CD arrived damaged. How will this loss be covered?
#a software warranty
8 A company informs the account manager that the installation of a new edge router at the customer remote branch location cannot be done at the scheduled time because of a large order that the branch office needs to complete. As a result, the end date of the
project must be adjusted to accommodate the additional time. What is the action should the account manager take?
#Adjust the timeline documentation to show the company how the delay will affect the project completion date.
9 NetworkingCompany completes the installation of a network upgrade for a retail customer. All of the onsite tests complete successfully and the customer IT staff approves the results of the tests. The manager of the retail store contacts NetworkingCompany to inform the company that the store will not pay for the upgrade until a recently purchased software
package is installed and tested on the network. Which two items that are contained in the proposal can the account manager refer to when discussing this issue with the store manager?(Choose two.)
#the project scope
#the terms and conditions
10 The operation of a new branch location network is delayed because a VPN cannot be configured and established between the branch location and the main office. It is determined that the router at the main office does not have enough memory and does not have the correct Cisco IOS version image to support the VPN features. To prevent this delay, this problem should have been identified and corrected during which part of the design project?
#the characterization of the existing network
11 The NetworkingCompany team is tasked to prepare an implementation schedule for a customer. It is determined that the new firewalls and wireless controllers that are specified in the design cannot be delivered and installed within the agreed upon time frame. The NetworkingCompany informs the customer of the problem. What two options can the NetworkingCompany team take to ensure the success of the project? (Choose two.)
#plan to add additional staff and resources to shorten the installation time after the new equipment is delivered
#renegotiate a new time frame with the customer to accommodate the delay
12 AAA Financial Services Company is performing implementation planning for a core switch upgrade. The company has 200 financial software programmers that work billable hours during the week. They have critical, scheduled money transfer transmissions that
occur at hourly intervals every night. There are two, two-hour long IT maintenance windows scheduled for software upgrades, one on Saturday and one on Sunday. The bank advertises online banking as available 24 hours on business days and 21 hours on the weekends. However, a network upgrade that is necessary to replace some switches is expected to take four hours. Because of rack constraints, this time includes three hours to remove the old switches before the ew switches can be installed and one hour to test the logical configuration. How should the implementation scheduling be handled
#Coordinate and publish an eight-hour downtime incorporating the Saturday window. This will allow four hours for installation and logical testing, one hour for troubleshooting and decision,
and three hours to roll back to the previous configuration if the new switching cannot pass the logical testing. Defer any software upgrades until the new network is proven to be working
correctly with the old software.
13 Included in a Bill of Materials (BOM) for a SOHO wired implementation is a Cisco 2811 router, Catalyst 2560 switch, four PCs, three laptops, and a networked printer. Wireless LAN capability will be implemented on this network. Which two equipment types must be added to the BOM to implement this request? (Choose two.)
#wireless NICs
#wireless access points
14 A customer has just taken delivery of a Cisco 2811 router and Catalyst 3560 switch. Included with the purchase is the SMARTnet Service. Which two resources are included with SMARTnet Service? (Choose two.)
#technical support from TAC
#maintenance releases for OS
15 A Cisco 1841 router has been purchased without an agreement for SMARTnet Service. What two items are guaranteed under the standard warranty? (Choose two.)
#replacement of defective physical media
#under normal use, replacement of defective hardware
16 Upon completion of a proposal, a network design team must sell their ideas to two key stakeholders. Who are these two stakeholders? (Choose two.)
#customers
#internal management
17 What are two important guidelines when creating a slide presentation for a meeting with a customer? (Choose two.)
#Use contrasting colors for background and text to aid visibility.
#Use bulleted text to lead the discussion.
18 In order to finalize a project proposal, an account manager of a networking company creates the terms and conditions section. What are two clauses that should be included in this section? (Choose two.)
#change order procedures
#problem resolution process
19 Which two items will a systems engineer include in an implementation plan? (Choose two.)
#references to design documents
#the steps to install and test the network
20 Which statement describes a phased installation into an existing network?
#A phased installation requires detailed planning in order to avoid disruption of user services.
#logical design
4 Which occurrence would indicate a failure of the design phase?
#The new network capacity is inadequate to support required traffic.
5 A network installation team is assigned to replace all core switches in an existing data center. No other upgrades are planned. Which kind of installation is this?
#a phased installation
6 What service is provided Cisco standard warranty?
#replacement of defected hardware
7 An upgraded version of the Cisco IOS has been purchased. However, the CD arrived damaged. How will this loss be covered?
#a software warranty
8 A company informs the account manager that the installation of a new edge router at the customer remote branch location cannot be done at the scheduled time because of a large order that the branch office needs to complete. As a result, the end date of the
project must be adjusted to accommodate the additional time. What is the action should the account manager take?
#Adjust the timeline documentation to show the company how the delay will affect the project completion date.
9 NetworkingCompany completes the installation of a network upgrade for a retail customer. All of the onsite tests complete successfully and the customer IT staff approves the results of the tests. The manager of the retail store contacts NetworkingCompany to inform the company that the store will not pay for the upgrade until a recently purchased software
package is installed and tested on the network. Which two items that are contained in the proposal can the account manager refer to when discussing this issue with the store manager?(Choose two.)
#the project scope
#the terms and conditions
10 The operation of a new branch location network is delayed because a VPN cannot be configured and established between the branch location and the main office. It is determined that the router at the main office does not have enough memory and does not have the correct Cisco IOS version image to support the VPN features. To prevent this delay, this problem should have been identified and corrected during which part of the design project?
#the characterization of the existing network
11 The NetworkingCompany team is tasked to prepare an implementation schedule for a customer. It is determined that the new firewalls and wireless controllers that are specified in the design cannot be delivered and installed within the agreed upon time frame. The NetworkingCompany informs the customer of the problem. What two options can the NetworkingCompany team take to ensure the success of the project? (Choose two.)
#plan to add additional staff and resources to shorten the installation time after the new equipment is delivered
#renegotiate a new time frame with the customer to accommodate the delay
12 AAA Financial Services Company is performing implementation planning for a core switch upgrade. The company has 200 financial software programmers that work billable hours during the week. They have critical, scheduled money transfer transmissions that
occur at hourly intervals every night. There are two, two-hour long IT maintenance windows scheduled for software upgrades, one on Saturday and one on Sunday. The bank advertises online banking as available 24 hours on business days and 21 hours on the weekends. However, a network upgrade that is necessary to replace some switches is expected to take four hours. Because of rack constraints, this time includes three hours to remove the old switches before the ew switches can be installed and one hour to test the logical configuration. How should the implementation scheduling be handled
#Coordinate and publish an eight-hour downtime incorporating the Saturday window. This will allow four hours for installation and logical testing, one hour for troubleshooting and decision,
and three hours to roll back to the previous configuration if the new switching cannot pass the logical testing. Defer any software upgrades until the new network is proven to be working
correctly with the old software.
13 Included in a Bill of Materials (BOM) for a SOHO wired implementation is a Cisco 2811 router, Catalyst 2560 switch, four PCs, three laptops, and a networked printer. Wireless LAN capability will be implemented on this network. Which two equipment types must be added to the BOM to implement this request? (Choose two.)
#wireless NICs
#wireless access points
14 A customer has just taken delivery of a Cisco 2811 router and Catalyst 3560 switch. Included with the purchase is the SMARTnet Service. Which two resources are included with SMARTnet Service? (Choose two.)
#technical support from TAC
#maintenance releases for OS
15 A Cisco 1841 router has been purchased without an agreement for SMARTnet Service. What two items are guaranteed under the standard warranty? (Choose two.)
#replacement of defective physical media
#under normal use, replacement of defective hardware
16 Upon completion of a proposal, a network design team must sell their ideas to two key stakeholders. Who are these two stakeholders? (Choose two.)
#customers
#internal management
17 What are two important guidelines when creating a slide presentation for a meeting with a customer? (Choose two.)
#Use contrasting colors for background and text to aid visibility.
#Use bulleted text to lead the discussion.
18 In order to finalize a project proposal, an account manager of a networking company creates the terms and conditions section. What are two clauses that should be included in this section? (Choose two.)
#change order procedures
#problem resolution process
19 Which two items will a systems engineer include in an implementation plan? (Choose two.)
#references to design documents
#the steps to install and test the network
20 Which statement describes a phased installation into an existing network?
#A phased installation requires detailed planning in order to avoid disruption of user services.
0 komentar:
Posting Komentar